FlySky FTr8B 2.4GHz 8CH Dual-antenna Dual-receiving AFHDS 3 Receiver PWM/PPM/i.BUS/S.BUS Output for RC Airplane Helicopter Vehicles

€29,24 €41,29
Banggood
FlySky FTr8B 2.4GHz 8CH Dual-antenna Dual-receiving AFHDS 3 Receiver PWM/PPM/i.BUS/S.BUS Output for RC Airplane Helicopter Vehicles
FlySky FTr8B 2.4GHz 8CH Dual-antenna Dual-receiving AFHDS 3 Receiver PWM/PPM/i.BUS/S.BUS Output for RC Airplane Helicopter Vehicles
€29,24 €41,29

SaveSavedRemoved 0

ONLY €29,24 for FlySky FTr8B 2.4GHz 8CH Dual-antenna Dual-receiving AFHDS 3 Receiver PWM/PPM/i.BUS/S.BUS Output for RC Airplane Helicopter Vehicles

 

*PLEASE NOTE that to avoid customs duties, select Banggood Express or EU Priority Line

 

For more FlySky offers – HERE
For Banggood Coupons see – HERE

 

 

Join Our Telegram Channel

 

FlySky FTr8B 2.4GHz 8CH Dual-antenna Dual-receiving AFHDS 3 Receiver PWM/PPM/i.BUS/S.BUS Output for RC Airplane Helicopter Vehicles

OVERVIEW:

The FTr8B receiver adopts Flysky  the third generation automatic frequency hopping digital system (AFHDS 3),which featyres dual antennas and bidirectional data transmission commonly known as telemetry plus an i-bus out/s.bus terminal and PWM/PPM switching at Channel 1.Compatible with all AFHDS 3 transmitters and RF modules.

Brand Name: FlySky

Item Name: FTr8B RC Receiver

Model: FTr8B

Weight: 11.3g

Size: 46.5*23.8*14.8 mm

PWM Channels: 7(Version 2.0 will be upgraded to 8 channels)

RF: 2.4GHz

2.4G Protocol:  AFHDS 3

Antenna:  Dual Antennas

Input Power:  3.5-9V

RSSI: Support

Data Output:  PWM/PPM/i.BUS out/S.BUS

Temperature Range:  -10℃ to +60℃

Humidity Limit:  20%-95%

Online Update:  Yes

Certification: CE,FCC ID: N4ZFTR8B

Model Type: fixed wing, gliders, helicopter, deltas wing, engineering vehicle, etc

Compatible products:

The receiver is compatible with all AFHDS3 transmitters and tuner (mainly including PL18, NB4, NB4 Lite, FRM302, etc).

Binding:

1. Press and hold the receiver BIND button [14] while powering on the receiver, release the BIND button after receiver is powered on, the LED [13] on the receiver will flash rapidly;

2. Put the transmitter into bind mode;

3. The binding process is complete when the LED on the receiver stops flashing and is on continuously.

– If a transmitter that has had its radio frequency (RF Standard) set to “AFHDS3 1 way” (please refer to your transmitter user manual) enters bind mode, the receiver LED will instead flash slowly. Exit bind mode on the transmitter and if the receiver LED stops flashing and is on continuously, the binding process is complete.

4. Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any problems arise.

Forced update:

If after a firmware update is performed and the transmitter is unable to bind to the receiver, the receiver may need to be put into forced update times.

1. Power on the receiver while pressing the BIND button [14] for then approximately ten seconds until the LED [13] flashes three times,release the BIND button.

2. Go to the RX Setup menu on your transmitter and select “RX Update”.

3. When the receiver LED flashes slowly, the update is successful.

Failsafe:

This function protects your vehicle by preventing unexpected behaviors in cases of signal lost.

1. Users should always input Fail Safe parameters before operating their vehicles. If the Fail Safe function has not been set on the transmitter and signal lost occurs, the receiver will continue to operate and maintain all output value at the last received instructions from the transmitter. If the Fail Safe parameters on the transmitter has set been set, the receiver will set output values according to user parameters during signal lost.

Package Included:

1 x FTr8B Receiver

 

ID:1800600 – SKUH08261

1800600CN
Kupon4U.com
Logo
Enable registration in settings - general